XL ledger panel 9 × 24
The 9 × 24 inch XL panel is half again as tall as a standard ledger panel, so a wall goes up in fewer, bolder courses and reads at a larger scale, which suits high walls, facades and big rooms. It comes split face in eight travertine and natural stone colours, and with honed and sandblasted 2D, 3D, XLP and XLP Plus faces for a cleaner, contemporary wall. One panel covers 1.5 square feet.
Specification
- Size
- 9 × 24 in (23 × 61 cm)
- Thickness
- 3–4 cm (approx.)
- Coverage
- 1.5 sq ft per panel
- Finish
- Split face, Honed, Sandblasted
- Stone
- Travertine
- Colours
- Light, Philadelphia, Rustic, Scabas, Silver, Mayra, K. Paşa, Bursa Beige, Roman VC 2D Honed, Başarır 2D Honed, Roman VC 3D Honed, Roman VC XLP Honed, Taja XLP Sandblasted, Roman VC XLP Plus Honed, Taja XLP Plus Sandblasted, Taja XLP Plus Split
- Origin
- Denizli, Turkey
Where it goes
Double-height walls, facades, lobbies, fireplace walls in large rooms, outdoor kitchens and garden walls.
Installation
- Fix to cement backer board, masonry or concrete with a polymer-modified thin-set mortar. Not to drywall on its own.
- Start at the bottom and work up, staggering the vertical joints from row to row.
- Back-butter each panel as well as combing the wall, for full contact.
- Seal the stone after installation, especially outdoors and around fireplaces.
General practice, not an installation guide. Follow the mortar maker's instructions and the building code where the wall is.
Colours
Light
Travertine · 23 × 61 cm
Philadelphia
Travertine · 23 × 61 cm
Rustic
Travertine · 23 × 61 cm
Scabas
Travertine · 23 × 61 cm
Silver
Travertine · 23 × 61 cm
Mayra
23 × 61 cm
K. Paşa
23 × 61 cm
Bursa Beige
23 × 61 cm
Roman VC 2D Honed
Travertine · 23 × 61 cm
Başarır 2D Honed
23 × 61 cm
Roman VC 3D Honed
Travertine · 23 × 61 cm
Roman VC XLP Honed
Travertine · 23 × 61 cm
Taja XLP Sandblasted
23 × 61 cm
Roman VC XLP Plus Honed
Travertine · 23 × 61 cm
Taja XLP Plus Sandblasted
23 × 61 cm
Taja XLP Plus Split
23 × 61 cm
Questions about this product
What is a split face ledger panel?
Natural stone split into strips, so the face is the rough surface of the break rather than a cut, then bonded into a single staggered panel. It gives the look of a dry-stacked stone wall and installs much faster than laying stones one by one.
How many panels do I need?
Divide the wall area in square feet by the panel's face: a 6 × 24 panel covers 1 sq ft, a 6 × 18 covers 0.75 and a 6 × 12 covers 0.5. Add 10 to 15 percent for cutting.
Can ledger panels go outdoors?
Yes, natural travertine and marble are used on exterior walls. In climates with freezing winters, seal the stone and install it over a substrate and with a mortar rated for exterior use.
What is the difference between travertine and marble panels?
Travertine has natural pores and warm beige, gold and silver tones. Marble is denser, with fewer pores, and gives the whites and greys. Both split well and both are quarried around Denizli.
The rest of the range
Split face ledger panel 6 × 24
The standard North American panel. 15 colours.
15 colours →
Split face ledger panel 6 × 18
A shorter panel for narrow walls and columns.
1 colour →
Split face ledger panel 6 × 12
The small panel, for tight spaces and detail.
2 colours →
Split face strips 5 × 15
Single 5 × 15 cm pieces, laid one by one. 6 colours.
6 colours →
Split face mosaic strips
Free length strips, 2.1 cm thick, in three widths.
3 colours →
Tumbled mosaics
Tumbled travertine bricks, 3 × 6 and 3 × 8 in.
3 colours →